Do It Yourself Computer - Assemble PC

Build-Your-Own-Computer.org - A Guide for the Do-It-Yourself PC Builder


Main Menu
Home

Computer Kits

Upgrade an Old Computer

Choosing Components

Assembling Your PC

Useful Links

Free backup is finally here.  Mozy Remote Backup.

Building a PC

Step 1:
Getting Organized

Step 2:
Configure Your Case

Step 3:
Installing Your CPU

Step 4:
Install Memory (RAM)

Step 5:
Install Motherboard

Step 6:
Install Hard Drive & CD/DVD

Step 7:
Install Video Card

Step 8:
Install Accessories

Step 9:
Initial Power-up

Step 10:
BIOS Settings

Step 11:
Install Operating System



Quick Links

Build a $500 PC

Build a $1000 Gaming PC

Build a High Performance PC

Motherboards

CPUs

Cooling

Memory (RAM)

Video Cards

Computer Cases

Storage (HDDs and More)

Monitors

Networking

Computer Glossary

DIY PC Blog

DIY PC Forum

Contact Us

Step 5: Installing your Hard Drive

<< Step 4: Install Motherboard
>> Step 6: Install Video Card

Before Installation

The worst part about installing hard drives is setting the jumpers on the drive so that it works correctly with your current hardware. You only need to worry about jumpers if you are using an IDE hard drive. IDE hard drives have settings for master, slave and cable select. This is because, for an IDE drive, it matters. For Serial ATA drives (SATA), you don’t need to worry about jumpers at all. Now that SATA is becoming much more prevalent than IDE, it is becoming a lot less likely that you will need to worry about jumpers during this process.

Before installation, inspect the inside of the computer’s case and determine where you want the drive to go. If you are using an IDE hard drive, you want to optimally connect the drive on a different IDE channel than your DVD/CD drives. Most motherboards have two IDE channel connectors. So you would put your disc drives on IDE2 and your hard drives on IDE1. For SATA drives, your life, again, got easier. SATA gets it’s own channel and, as of this date, SATA DVD drives are very uncommon.

Materials Required

  • Hard Drive and/or CD/DVD Drive
  • Controller card (optional; use this if you don’t have a spare connector on the motherboard or space on an existing ribbon cable to connect your drive to. Make sure you get one that matches your drive – Serial ATA for an SATA drive; ATA/100 or ATA/133 for an IDE drive; SCSI for a SCSI drive.)
  • Data cable for the drive (SATA or IDE, as appropriate for your drive type)
  • Ultimate Boot CD (if you want to clone your old hard drive to your new one)

How will you be using your new drive?

If you are replacing your primary hard drive, make sure you back up any data you want to save before you start. If you don’t want to reinstall Windows, you can clone the contents of your old hard drive to your new one using the setup utilities that hard drive manufacturers provide, or you can use a specific cloning program like HDClone or PC Inspector Clone Maxx. All of the above-mentioned utilities are available on the Ultimate Boot CD, so you can download and burn that and then choose the utility that is easiest for you to understand. (If you don’t have access to a high-speed internet connection, you can order a CD for a small fee.)

If you are willing to reinstall Windows, make sure you have discs for Windows and all your programs. This will prevent frustrations about losing programs after you have already formatted your computer.

If you are simply installing a secondary hard drive for storage, you don’t have to make any changes to the configuration of your current hard drive. If, however, you are installing a second IDE drive, it is possible that you will need to alter the jumper configuration of your primary hard drive. If your current hard drive is set as “Cable Select” (meaning it is the only drive on the channel), then you may need to change it to “Master” which will allow you to add the second hard drive as a slave (see below).

Setting Jumpers: IDE Drives

If you are using an old (very old!) IDE Drive, the this information is for you. SATA Drive owners can skip ahead! IDE can accommodate two drives per channel, most modern motherboards will support only one channel (if any at all). So that means with a single channel (or a single motherboard connection--usually labaled PATA) you will be able to support up to two PATA/IDE devices. Nowadays, the most common use for PATA is connecting non-SATA CD/DVD drives. So, here's a little primer for you... The primary drive on a channel is called the Master, and the secondary one is called the Slave. If you are booting from an IDE hard drive, you should make that device the Master and any CD/DVD device the Slave. If you are only using your PATA interface for a CD/DVD, the either Master or Slave will work. However, I'm "old-school" and a little obsessive about how I configure my systems--if I only have one device attached to a PATA/IDE channel, I always configure it as Master.

Most drives come from the factory jumpered as masters, so if you want to use one as a slave, you will need to switch the drive's jumpers. Each manufacturer has different jumper settings, so I can't give you exact directions here, But... there is often a diagram on the top of the drive telling you how to set the jumpers, and if not, you can refer to your hard drives manual for the correct settings. If you don't have the manual, try searching the web for a manual by using the drive's make and model number.

Setting Jumpers: SATA Drives

You're in luck. No jumper settings here! SATA drives only connect one-to-a-channel, so no jumper settings are needed.

Drive Installation

  1. Turn off the computer, unplug it, and take off the case. At this point, you may want to make some quick sketches of just how everything is in there: Which direction is everything facing? Where and how are the cables connected? For some people, such sketches help to put everything back when you are done.
  2. If you are replacing your old hard drive, remove the cables from the old drive. You will see both a ribbon cable and a small power plug. Do not force them out. The ribbon cable is usually quite easy to remove. Sometimes, though, the power connector can become stuck. Just rock it back and forth (lengthwise along the narrow side of the drive), taking care not to rip the connector off the drive. Then remove the mounting screws that hold the drive to the case frame. Sometimes, you may need to tip the case or get into some strange positions to reach all the screws; other times, the hard drive is mounted in a cage that you’ll be able to take out to get to the other side of the drives. Finally, remove the old drive from the case. Be sure not to bump anything too hard on the way out.
  3. If you are replacing the old drive, slide the new drive in right where the other one came out. If you are adding a second drive, just pick any empty drive bay – one a bit below the current drive might work best, because it will make it easier to route cables. If you are installing a 3.5″ drive into a 5.25″ drive bay, you may need to add rails or a mounting bracket to make it fit. Screw the drive into place, making sure the screws aren’t going in crooked. Don’t force them.
  4. If you need a separate controller card, install it now into any unused motherboard slot. Chances are that you don’t need to worry about this. It is usually only necessary if you want to add more IDE drives than your computer will support with it’s two built-in channels. If you are using SATA, your motherboard likely comes with enough SATA ports. If not, you can extend it using a controller card just the same way as with IDE.
  5. SATA Drive
    Attach SATA Cable to HDD
    SATA Drive
    Attach SATA Cable to Motherboard
  6. Attach the cables to the hard drive and to the motherboard or controller card if necessary. There are two cables: the ribbon cable (or SATA cable) and the power cable. The ribbon cable goes from the controller to the drive. Most cables are keyed to the connector so they only go in one way; if the cable isn’t going in, try flipping it over. Don’t force it. If you are adding a second drive, simply choose a connector on the same ribbon cable that is not used. Most IDE ribbon cables come with three connectors: one on the end (usually black) and one mid-way (usually gray), then one further away on the other end which connects to the motherboard (usually blue, green, or red). In general, the master drive should use the black connector on the end and the slave should use the gray connector in the middle, but if each drive is set either as master or slave, the position is not as important. On a SATA hard drive, position of the drives on the cable does not matter at all because a SATA cable only accomodates one drive.
  7. Plug the system in and turn it on. It is best to leave the case cover off for now in case you need to fiddle with something or troubleshoot the installation.
  8. If you did not use a controller card, enter the BIOS (usually by pressing the F1, F2, F10, F12, or Delete key when you see the Power-On Self-Test or the manufacturer logo). Check the BIOS to make sure that the drives are all being recognized. If you installed a drive on a connector that was not in use, you may have to set the corresponding drive to “Auto.” If your BIOS has an auto-detect feature, you can use that as well. If you did use a controller card, it will pop up a screen showing the name of the card and any drives it has detected.
  9. If the drives are not being recognized, check that both power and data cables are in tightly (including the motherboard end for the data cables), and that the jumpers are set correctly. If they are all recognized correctly, let’s move to the next section.

Software Installation/Cloning

Now that your new drive is installed, we can move on and get it set up with Windows. If you are replacing your current drive and cloning it to your new drive, you will need to connect both drives. Change any necessary jumpers (see “Setting Jumpers” above) so that both drives as well as a CD drive are recognized. At this stage it is not important to screw in your old drive; you can just rest it somewhere convenient, but don’t leave it hanging in midair. Boot from the Ultimate Boot CD, and select the utility you want to use to clone the drive. Go through the appropriate prompts, making sure to select your older drive as the source and your newer one as the destination (pay careful attention to the hard drive sizes indicated by the cloning program). You don’t want to clone your new drive with nothing on it to your old drive with all your data!

If you are replacing your current drive but not cloning its contents to the new drive, put your Windows CD in the drive and boot from it. You will be prompted during the first part of setup to partition and format your drive; if you are using Windows 2000, XP or Vista, make sure to use the NTFS file system.

If you are simply installing a secondary drive, boot into Windows. In Windows 2000/XP/Vista, your new drive will not appear at all in My Computer until you format it. In Windows 9x/ME, it will appear, but you will need to right-click on the new drive and choose “Format” from the menu. To format the drive in Windows 2000 or XP, right-click on My Computer and go to “Manage”. In the window that comes up, click Disk Management in the left pane. Once it loads, you should see an “Initialize Disk” wizard pop up. Partition and format the disk to your liking, but make sure not to convert it to a dynamic disk, as doing so will provide plenty of annoyances down the road.

Finished!

Congratulations, your new drive is installed!  Now that you have installing your hard drive under your belt, you might be interested in partitioning your hard drive(that means dividing your space so you can separate data).

Next Step?

You’ll need to backup and restore your data to your new hard drive. This is VERY time-consuming usually. PCMech has long been a fan of Acronis True Image. This full-featured backup/restore utility from a trusted company will help you clone your PC and restore it to your new hard drive.




Return to Build Your Own Computer Home Page